Getting Familiar with Plumbing: A Must for Bathtub Installation

Click Here To Read More

They are making several great pointers about How to Install a Bathtub as a whole in the content down the page.


Tools You Need to Install a New Bathtub
Setting up a bath tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult project. If the old tub is readily available, the project can relocate immediately; if you have to open up a wall surface to eliminate the old tub and position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as embeded in the brand-new one. See to it you have qualified on your own for the work and also are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is better to think about utilizing one before you begin. Opportunities are you may need a professional plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your restroom if you have actually currently gotten a new tub and also don't require to alter the plan of your previous water supply pipes.
Your tools and also product list ought to consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Setup


    Firstly, the supporting frame provided with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bathtub.
    Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.

    Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited accessibility that is commonly the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this process. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing compound.
    Prior to proceeding to fit the new faucets, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Setting up the Bathtub


    Making use of the two wooden boards under its feet, place the bath tub in the required position. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
    The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level as well as changing the feet on the bathtub up until the level reviews level.
    To install taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression join; then do the same for the other faucet.
    Activate the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and likewise inspect the overflow electrical outlet and the normal electrical outlet for leaks.
    Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the tub must wait till the bathtub has been used at the very least when as this will resolve it into its last position.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Protect the faucet in place with the manufacturer supplied backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind must be linked to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to permeate the wall surface in between the bath and the tiling, bring about problems with moisture and feasible leaks to the ceiling below.
    You can select from a range of coloured sealers to assimilate your components and also installations. They are offered in tubes and also cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealant can break fairly very early if you do not take into consideration this motion before securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive as well as cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub

    Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Write feedback down below. We will be interested to hear your thoughts about this page. We hope to see you back again in the future. Liked our content? Please share it. Let somebody else check it out. Thank you for your time. Visit us again soon.


    Request An Estimate

    Leave a Reply

    Your email address will not be published. Required fields are marked *